A P P E N D I X
E
Installing the Wall Mount for the Cisco Unified
IP Phone 6901 and 6911
This appendix contains information on installing the wall mount for use with the Cisco Unified IP Phone
6901 and 6911 phones.
Installing a Wall Mount for the Cisco Unified IP Phone 6901
The following section describes how to install the Wall Mount plate for use with the
Cisco Unified IP Phone 6901.
Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for
mounting the Cisco Unified IP Phone 6901. The wall mount plate must be ordered separately from the
phone.
Figure E-1 shows a list of items required to mount the Cisco Unified IP Phone 6901 on the wall using
the Leviton Wall Mount plate.
Figure E-1
Leviton Wall Mount Plate
4
A
B
6
8
7
1
2
1
RJ45 Connector
2
Leviton Wall Mount Plate
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-1
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Installing the Phone on Wall Mount Plate
To install the phone on the wall mount plate, follow these steps:
Procedure
Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone (Figure E-3).
Step 1
Figure E-3
RJ45 Connector in the Phone Jack
2
1
1
2
Network Port on the Phone
RJ45 Connector
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-3
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Step 2
Figure E-4
RJ45 Connector in the Wall Mount Jack
2
3
1
4
1
2
Network Port on the Phone
RJ45 Connector
3
4
Wall Mount Plate
Network Port on the Wall Mount Plate
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-4
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Step 3
Slip the mounting holes on the base of the wall mount plate and over the wall mount pins (Figure E-5).
Figure E-5
Mounting Holes
1
2
1
2
Mounting Hole on the Phone
Wall Mount Pin on the Wall Mount Plate
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-5
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Step 4
Figure E-6 Sliding the IP Phone
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-6
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
The following section describes how to install the wall mount for use with the Cisco Unified IP Phone
6911.
Figure E-7 shows a list of items included in the Wall Mount Kit for the Cisco Unified IP Phone 6911.
Figure E-7
Wall Mount Kit for Cisco Unified IP Phone 6911
Screws
(4)
Anchors
(4)
Machine
screws
(2)
Phone bracket
Wall bracket
Ethernet
cable
Lock-down
key
The package includes the following items:
•
•
•
•
•
•
One phone bracket
One wall bracket
Four 10-12x1 inch Phillips-head screws with 4 anchors
Two 4-40x1/4 inch machine screws
One six-inch Ethernet cable
One key if the bracket includes the optional lock
Before You Begin
You will need these tools to install the bracket:
•
•
#1 and #2 Phillips-head screwdrivers
Level
You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does
not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a
regular telephone jack. For more information on phone installation requirements and warnings, see the
Setting Up the Cisco Unified IP Phone chapter.
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-7
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Installing the Bracket
To install the phone on the wall, follow these steps:
Procedure
Step 1
Mount the wall bracket in the desired location (Figure E-8). You can install the wall bracket over an
Ethernet jack, or you can run the Ethernet network cable to a jack nearby.
a. Use the Level to ensure the wall bracket is level, then use a pencil to mark the screw holes.
b. Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the
anchor into the wall to make markings on the wall.
c. Screw the anchor clockwise into the wall until it is seated flush.
d. Use the included screws and a #2 Phillips-head screwdriver to attach the wall bracket to the wall.
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-8
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Figure E-8
Mounting the Wall Bracket
A
B
Mark mounting
holes through
bracket on wall
Level wall
bracket on wall
C
D
Screw bracket
to wall using
Phillips head
screws
Insert anchors
into wall
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-9
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Step 2
a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached
cords from the base of the phone.
b. Remove the label covers that are concealing the screw holes.
c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The phone’s
ports should be accessible through the holes in the bracket.
d. Secure the phone bracket to the IP Phone with the Phillips-head screws.
e. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the
clips incorporated into the phone body.
Figure E-9
Attaching the Phone Bracket
Screw holes
Slot for
mounting tabs
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-10
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Step 3
Remove the handset wall hookswitch in the handset rest, rotate the hookswitch by 180 degrees, and
reinsert the hookswitch. The hookswitch should have a lip on which the handset catches when the phone
Figure E-10
Preparing the Handset Hookswitch
1
2
3
4
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-11
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Step 4
Attach the Ethernet cable to the 10/100 SW network port and wall jack.
If you are connecting a network device (such as a computer) to the phone, attach the cable to the
10/100 PC access port.
If you are using an external power supply, plug the power cord into the phone and dress the cord by
clipping it into the clips incorporated into the phone body next to the 10/100 PC port (Figure E-11).
Figure E-11
Attaching the Cables
Wall bracket
Phone bracket
Network
port
Handset port
AC adapter
port
Phone bracket
cable access hole
U-shaped holes
for cables
(optional power
cable)
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-12
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Step 5
Step 6
Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots
on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall
behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket. The
phone and wall brackets’ openings together form circular openings with room for one cable per opening
Use the locking key to lock the phone to the wall bracket.
Figure E-12
Attaching the Phone to the Wall Bracket
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-13
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing a Wall Mount for the Cisco Unified IP Phone 6911
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
E-14
|