I N S T A L L A T I O N I N S T R U C T I O N S
CTA-2536
Internal Dual Stud Wall Plate
The CTA-2536 Dual Stud Wall Plate provides a
mounting solution for the following wall arms:
•
•
CTA-025 Single Stud Wall Arm
WMA-300 Wall Mount Arm
The CTA-2536 has a maximum weight capacity of
150 lbs. (68.0 kg).
CTA-2536 Internal Dual Stud Wall Plate
BEFORE YOU BEGIN
•
CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty,
thoroughly study all instructions and illustrations before you begin to install the CTA-2536. Pay particular
attention to the Warnings and Cautions in this document.
•
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
CHIEF MANUFACTURING INC.
8809-000028 (Rev. A)
2004 Chief Manufacturing
11/04
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
Installation Instructions
CTA-2536
CONTENTS
INSPECT THE UNIT BEFORE
PARTS ..............................................................................2
INSPECT THE UNIT BEFORE INSTALLING ..............3
TOOLS REQUIRED FOR INSTALLATION..................3
INSTRUCTIONS..............................................................4
Determine a Suitable Mounting Location .....................4
Installing the Wall Plate ................................................4
Attaching Wall Arm to Wall Plate ................................5
Attaching Front Cover...................................................5
Connecting NPT Pipe or Nipple to Wall Arm...............5
INSTALLING
Unpack the carton. Carefully inspect the parts for
shipping damage. Verify contents listed in Table 1.
If you are missing any of the listed parts, contact
Customer Service at: 1-800/582-6480.300.
Table 1. Shipping Contents
ITEM DESCRIPTION
QTY
10
20
30
40
50
60
70
Wall Plate
1
6
6
6
6
6
1
5/16 X 2.5” Lag Bolt
5/16 Flat Washer
M8 Flat Washer
M8 Lock Washer
M8 X 16mm Button Head Cap Screw
M5 Allen Key
TOOLS REQUIRED FOR
INSTALLATION
The tools required for installation are as follows:
•
•
•
•
•
Electric drill and bit set
Stud sensor (mechanical or electronic)
½” box-end wrench or ratchet with ½” socket
13mm box-end wrench or ratchet with 13mm socket
Level
NOTE: Other tools may be required depending on
your method of installation.
3
Installation Instructions
CTA-2536
INSTRUCTIONS
STEP 1
Determine a Suitable Mounting Location
NOTE: The wall plate (10) must be mounted to
wood studs that are 16” apart on center.
See Figure 2.
16”
1. Locate the wall plate (10), six lag bolts (20) and
six flat washers (30).
WARNING
It is the installer’s responsibility to verify that the
structure to which the mount is anchored will
safely support five times the combined load of all
attached components and equipment.
2. Determine a suitable mounting location. Keep in
mind that the wall plate (10) must be mounted to
wood studs that are 16” apart on center.
3. Using a stud sensor, locate the two wood studs
where you will mount the wall plate (10).
STEP 2
Installing the Wall Plate
Figure 2. Install the Wall Plate
1. Holding the wall plate (10) against the wall, use a
pencil, awl, or small nail to mark the mounting
holes where the top two pilot holes will be drilled
into the center of the wood studs. Make sure that
the mounting holes in the unit are level.
2. Using a 15/64” drill bit, drill two pilot holes for
anchoring the wall plate (10). See Figure 2.
3. Using two 5/16” lag bolts (20) and two 5/16” flat
washers (30), fasten the wall plate (10) to the
wall. See Figure 2.
4. Repeat step 2 to drill four more pilot holes into
the wood studs for the middle and bottom
mounting holes.
5. Repeat step 3 to install the remaining four 5/16”
lag bolts (20) and four 5/16” flat washers (30)
into the wood studs and to secure the wall plate
(10).
4
Installation Instructions
CTA-2536
STEP 3
Attaching Wall Arm to Wall Plate
1. Locate the wall arm, six M8 flat washers (40),
six M8 lock washers (50), and six M8 x 16mm
button head screws (60). See Figure 3.
2. Attach wall arm to wall plate (10) as follows:
a. Using the parts (40, 50, and 60) described in
step 1 in the top mounting holes, attach the
wall arm to the wall plate (10).
b. Using the parts (40, 50, and 60) described in
step 1 in the bottom mounting holes, attach
the wall arm to the wall plate (10).
Figure 3. Attach Wall Arm to Wall Plate
c. Using the M5 Allen key (70), tighten the six
M8 x 16mm button head screws (60) to
secure the wall arm to the wall plate (10).
STEP 4 [REFERENCE ONLY]
Attaching Front Cover
1. Locate front cover and four M4 x 8mm Phillips
head cap screws (shipped with wall arm).
NOTES
•
•
The front cover may be partially removed
and reinstalled to conceal power/audio/video
cables after the TV/Mount is installed.
You may remove one or both knockouts on
cover to assist routing to wall through cover.
Figure 4. Install Cover on Wall Arm
2. Install the front cover using four M4 8mm
Phillips head cap screws. See Figure 4.
STEP 5 [REFERENCE ONLY]
Connecting NPT Pipe or Nipple to Wall Arm
1. Locate M6 x 6mm set screw and 1-1/2” NPT
pipe or nipple (supplied with TV Mount or
purchased separately).
2. Connect the 1-1/2” NPT pipe or nipple (supplied
with TV Mount or purchased separately) to the
wall arm. See Figure 5.
3. Using the M3 Allen key, install the M6 x 6mm
set screw. Tighten the set screw.
(Supplied with TV Mount
or purchased separately)
WARNING
Make sure to tighten the M6 x 6mm set screw to
prevent equipment damage or personal injury.
Figure 5. Connect NPT Pipe or Nipple
to Wall Arm
5
|