• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws have not come loose.
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
CAT EYE ASTRALE 8
CYCLOCOMPUTER CC-CD200N
E: Owner’s Manual
®
Warning
• Avoid unnecessary prolonged exposure to the sun.
• Never attempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Important
Note
ASTRALE8
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002/2003 CAT EYE Co. Ltd.
Mount The Bracket
3 Secure the cord by fastening it to the frame with zip ties at regular intervals.
CCMCD2N-030531 066600252
1
Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound. When you need to
remove the computer, press the lever on the handlebar bracket and slide the computer
forward.
Please read these instructions carefully before installing or
using the CAT EYE ASTRALE 8.
Please keep this manual in a safe place for future reference.
Note
Allow enough wire clearance in the area marked with
to insure you can turn
the handlebars all the way from side to side without pulling the wire.
Installation of the Computer on Your Bike
The computer comes with the following parts:
1
Lever
3
2
3
8
Slide
1
9
4
1
9
5
2
8
6
Basic Functions Test
7
4 Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence
1 Bracket
2 Cord
5 Sensor Rubber Pad
6 Wheel Magnet
7 Cadence Magnet
8 Bracket Rubber Pad
9 Nylon Ties (10)
(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly.
When you receive a signal, tightly secure the sensor so it does not move.
3 Speed Sensor
(Long Cord)
4 Cadence Sensor
(Short Cord)
Note
When the computer does not indicate the speed/cadence, check the position of the
magnet and the sensor.
Rotate the crank arm
Rotate the rear wheel.
OK
OK
1
Mount the wheel magnet and speed sensor
1 • Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the
magnet faces the sensor.
•
Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9.
Computer Set-up
You need to know
your tire size or the
roll out length of your
tire in MM's.
Note
The nylon ties can only be used once, please install with care.
!
(For first use or after replacing the battery)
9
9
6
Contact Point
Rear wheel
spoke
3
L mm
The smooth edge of the zip
tie should be on the outside
Sensor Side
Refer to the chart below for
approximate tire lengths.
Left chainstay
Important Note
L(mm)
Tire size
Mount the magnets 6 and the sensors 3 in the appropriate positions so that the
center of each magnet 6 aligns with the marked sensor line when the rear wheel
and crank arm are rotated. The magnet should be no more than 5mm from the sensor.
12 x1.75
14 x 1.50
14 x 1.75
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
935
1020
1055
1185
1195
1340
1350
1515
1615
1770
1785
1753
SET Button
AC Button
START/STOP Button
MODE Button
Left chainstay
3
Rear wheel spoke
AC Button
6
All Clear
1 Push the AC button on the backside.
Center
3
* Push the AC button when using this
system for the first time and every
time the battery is replaced.
24 x 3/4 Tubular 1785
Adjust
Marked Line
6
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
1795
1905
1890
1925
1965
1920
1913
1952
1953
1970
2068
2100
2005
2010
2023
2050
2055
2068
2070
2083
2170
2155
2161
2161
2169
2090
2125
2105
2070
2080
2086
2096
2105
2136
2170
2155
2130
2168
2180
2200
Within 5 mm
Measurement Selection
2 Select the measurement unit, kilometer or mile, by pushing the
MODE button. Fix it by pushing the SET button.
Mount the cadence magnet and cadence sensor.
• Mount the cadence magnet 7 on the left crank arm so that it faces the sensor.
• Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9.
26 x 1(59)
26 x 1(65)
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 35A
650 x 38A
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C
2
Kilometer
Mile
MODE
9
SET
9
Inward Side of
Sensor Side
7
The Crank Arm
3
Left Chain Stay
Set The Tire Circumference
Set the tire circumference in mm.
Refer to the chart shown on the right.
Setting is fixed and completed by pushing the SET button.
3
Important Note
Note
When the crank is spinning, the center of the magnet 7 should pass in front of the sensor
4 marking line. The distance between the sensor and the magnet 7 should be within
5mm. After adjusting the magnet and sensor, secure tightly with nylon ties.
Increase the
number
Max. 2999 mm
Left Chain Stay
MODE
4
SET
Decrease
the number
Min. 10 mm
7
Marked Line
START/STOP
Crank Arm
4
Center
Preparation Complete.
7
(the screen will show the time measurement in this state)
Adjust
Within 5 mm
Tire size is usually shown on
the sidewall of tires.
* The auto mode is ON in this state.
|