Candy Washer CBL140 User Manual

Washing machine

Instructions for use

CBL 140

M) N.B!

If the appliance is installed on a carpeted floor ensure that the ventilation holes on the

General delivery notes

Please check that the following items are delivered with the appliance:

base of the appliance are not obstructed.

N) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do

not tamper with the appliance.

- Instruction manual

Consult only the Authorised Technical Support Service for possible repair and ask them to

use original spare parts.

- Certificate of guarantee

- Inlet hose

Failure to comply with the above can compromise the safety of the appliance.

O) If the appliance’s power cable should ever need replacing, consult the Authorised

Technical Support Service

- Liquid detergent compartment

- 32 minute programme dosing scoop

Check that no damage has occurred during transit, and if so, call your nearest Authorised

Technical Support Service agent (see Customer Service)

Quick start

Safety notes.

Washing

Open the door with the special DOOR OPEN button “B” (Fig. 1, page 7)

Note:

Select laundry and put it in the machine

Close the door

for cleaning or maintenance of the washing machine

Put detergent in the compartments as indicated in the programme guide in this instruction

manual

A) Pull out the plug

Select programme

B) Turn off the tap

C) Candy equips all its appliances with earthing. Ensure that the mains supply is earthed,

and if it is not, seek assistance from a qualified person.

Press additional function buttons (if required)

Press the Start button (page 7)

D) Do not touch the appliance when hands or feet are wet or damp. Do not use the appliance

with bare feet.

After few seconds the appliance starts working.

E) The use of adapters, multiple connectors and/or extensions is not recommended.

After washing

Note:

The indicator light “end cycle” will go on.

Wait for the door lock to be released

water temperature can reach 90°C during the wash cycle

(about 2 minutes after the programme has finished).

Switch off the washing machine by pressing the

Start button and turning the selector to OFF.

Open the door and remove the laundry

F) Check there is no water left in the drum before opening the door.

G) Do not allow children or unauthorised persons to use the appliance without supervision.

H) Do not pull the power cable or the appliance itself to remove the plug from the socket.

I) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)

L) When moving the appliance never lift it by the controls or by the detergent drawer.

When in transit never rest the door against the trolley or transport the appliance without

the polystyrene base.

Description of controls

Useful advice for users

Fig. 1

Tips on using your domestic appliance in the most environmentally-friendly and economical

way

Do a full load in your washing machine

To prevent any possible waste of energy, water or detergent we recommend that you put a

full load in your washing machine, not exceed the maximum loads shown below:

Cotton and linen 4,5 kg

Mixed

1,5 kg

Very delicate

Wool

A D E F G

Door open button

H B C

Up to 50% energy saving can be made with one full load compared to two half load washes

When is prewashing really needed?

Only with particularly dirty loads!

A special safety device prevents the porthole from being opened immediately after the end of

Energy savings of 5 to 15% are made by not selecting the prewash option for normal soiled

laundry.

the cycle. Wait for 2 minutes after the wash cycle has finished before opening the door.

Start button

Which wash temperature should you choose?

Press to start the selected cycle (according to the selected cycle one indicator lights will go on).

Note: When the START button has been pressed, the appliance can take few seconds

before stars working.

Using stain removers before machine washing reduces the need to wash at temperatures

over 60°C.

Energy savings of up to 50% can be made by using a 60°C wash temperature rather than

90°C

Changing the settings after the programmes has started (Pause)

Once the programme has started the settings can only altered by pressing the relevant buttons.

Release the START button.

The indicator lights time to end will flash, make your changes and press the START button

once more.

If you wish to add or remove items during washing, release the START button and wait 2

minutes until the safety device unlocks the door.

When you have carried out the manoeuvre, close the door, press START button and the

appliance will continue working where it left off.

Cancelling a selected programme

The programme can be cancelled at any time in the following way:

Release the START button

Turn the selector knob first to the OFF position and then away from it

Wait around 5 seconds

The machine will be ready for another programme or to be switched off.

ATTENTION:

The door cannot be opened until the START button has been released

The machine on indicator light is illuminated when the on/off button is pressed.

STAIN BUSTER button

Indicator lights showing which phase the programme is in

This function which is available on all cotton programmes is very useful for heavy soiling.

The temperature is kept constant throughout all the wash phases and the programme is

extended to ensure an extra deep cleaning performance.

Lights will come on to indicate the wash stage of the programme.

QUICK WASH button

Pressing this button reduces the time of the wash programme by a maximum of 50 minutes

depending on the programme and the temperature selected. The quick wash button can be

used for washing loads of 1 to 4,5 kg. This option may only be utilised on cottons and

synthetics programmes.

VARIABLE SPIN SPEED selector

Can be turned in either direction

QUICK IRON button

The spin stage plays a very important role in preparing the

laundry for efficient drying and your model offers maximum

flexibility to suit all your requirements.

The Quick Iron function minimizes creases as much as possible with a uniquely designed

anti-crease system that is tailored to specific fabrics.

MIXED FABRICS - the water is gradually cooled throughout the final two rinses with no

spinning and then a delicate spin assures the maximum relaxation of the fabrics.

DELICATE FABRICS – final two rinses with no spinning and then the fabrics are left in water

until it is time to unload. When you are ready to unload, press the Quick Iron button – this will

drain and spin ready for emptying

The selector can be turned to reduce the maximum spin

speed, right up to eliminating the spin completely (position

In programmes for mixed fibres, synthetics and delicates,

the washing machine automatically lowers the spin speed.

In order not to damage fabrics, it is not possible to increase this spin speeds.

RESISTANT FABRICS AND WOOLLENS - at the end of the final rinse, the fabrics are left in

water until it is time to unload. When you are ready to unload, press the Quick Iron button –

this will drain and spin ready for emptying

If you do not want to spin the clothes and activate drain only :

◆ release the START button

Note: this model is fitted with an electronic device that

checks the load is balanced correctly. If the load is

slightly unbalanced the machine will re-balance it

automatically to carry out the normal spin.

If, after several attempts, balance is not restored, a

reduced spin speed will be used.

If loads are seriously unbalanced the spin stage will be

cancelled.

This helps limit vibration, reduce noise output and

improve the washing machine’s lifespan.

◆ turn the selector knob to the OFF position

◆ select programme drain

◆ wait around 5 seconds

◆ switch on the appliance again by pressing the START button

EXTRA RINSE button

This function will allow an extra rinse or more water added at the rinse stage – depending on

the programme selected. This is particularly important for avoiding skin irritation from

detergent residues for people with particularly sensitive skin.

The extra rinse button is also recommended when washing heavily soiled fabrics, requiring

the use of a lot of detergent, or when washing items made of towelling, whose fibres have a

greater tendency to retain detergent.

PROGRAMME Selector with OFF position

Detergent drawer

ROTATES IN BOTH DIRECTIONS

The On/Off indicator light will go on

The detergent draw is split into 4 compartments:

- the first, labelled "I", is for prewash detergent

- the second, labelled "II", is for main wash detergent

The tables describe the washing programme on the basis of the number or symbol chosen.

N.B. To switch off the indicator light

move the programme selector to the

OFF position

If liquid detergents are used, please insert the special

container supplied into the compartment marked “II” in the

detergent drawer. This ensures that the liquid detergent

enters the drum at the right stage of the wash cycle.

Note: some detergents are difficult to remove. For these,

we recommend you use the special dispenser which is

placed in the drum.

- the third, labelled "

", is for bleaching agents.

The machine is programmed to automatically take up the bleach during the first rinse in

cotton cycles.

Note: only put liquid products in the third and fourth

compartments.

- the fourth, labelled "

brighteners etc.

" is for special additives, fabric softeners, fragrances, starch,

The machine is programmed to automatically take up additives during the final rinse stage for

all wash cycles.

“MIX & WASH SYSTEM” PROGRAMME 40°

_{An ecological wash system which permits differe}M_{nt t}&_ypW_{es of fabric to be washed together.}

Programme selector

For the various types of fabrics and various degrees of dirt the washing machine has 4

different programme bands according to: wash cycle, temperature and lenght of cycle (see

table of washing cycle programmes).

32 MINUTE RAPID PROGRAMME 50°C

The 32 minute rapid programme allows a complete washing cycle to be carried out in

approximately 30 minutes, with up to a maximum load of 2 kg and a temperature of 50°C.

The maximum quantity of detergent that can be used is marked on the enclosed 32 minute

gauge. The detergent must be placed in the main wash compartment (marked II) in the

detergent dispenser.

1 Resistants Fabrics COTTONS

The programmes have been designed for a maximum wash and the rinses, with spin

intervals, ensure perfect rinsing.

The final spin gives more efficient removal of water.

2 Mixed and Synthetic Fabrics SYNTHETICS

Main wash

Automatic Variable Capacity

The washing machine is fitted with an automatic reduction in consumption system (known as

The main wash and the rinse gives best results thanks to the rotation rhythms of the drum

and to the water levels.

A gentle spin will mean that the fabrics become less creased.

Automatic Variable Capacity).

3 Special Delicate Fibres DELICATES

This system enables the machine to use the amount of water needed to wash and rinse the

laundry in relation to the particular load.

This is a new wash cycle which alternates washing and soaking and is particularly

recommended for very delicate fabrics such as Pure Machine Washable Wool. The wash

cycle and rinses are carried out with high water levels to ensure best results.

This results in a reduction in the amount of water used and electricity needed to heat it to the

minimum required, without in any way compromising the washing and rinsing performance.

In fact the amount of water and electricity used will always be appropriate for the amount of

washing.

4. SPECIALS

HAND WASH 30°C

The washing machine therefore ensures you achieve excellent washing results whilst

respecting the environment and saving you money.

This washing machine also has a gentle Hand Wash programme cycle. This programme

allows a complete washing cycle for garments specified as “Hand Wash only” on the fabric

care label. The programme has a temperature of 30°C and concludes with 2 rinses and a

slow spin.

SPECIAL “RINSE” PROGRAMME

This programme carries out three rinses with a spin at 800 rpm (which can be reduced or

excluded by using the variable spin speed selector). It can be used for rinsing any type of

fabric, eg. use after hand-washing.

SPECIAL “FAST SPIN” PROGRAMME

Programme “FAST SPIN” carries out a spin at 1400 rpm (which can be reduced by using the

variable spin speed selector).

DRAIN ONLY

This programme drains out the water.

Sorting the laundry

The correct way to wash

It is recommended you wash only items which are machine washable with water and

detergent and not dry-clean items.

Preparing the laundry

A) Select the laundry.

If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.

Loading the laundry

B) Open the porthole.

Sort the laundry according to fabric type, degree of soiling and wash temperature: Always

follow the wash care advice on the garment label for the most suitable care and

treatment of the laundry

C) Put the laundry in the washing machine.

Close the porthole again, ensuring that no items of

laundry are obstructing the lock.

Laundry for hot wash

Coloured, easy-care materials

Delicates and wool

Putting detergent in machine

D) Open the drawer, choose the detergent and put in the

correct amount, according to the manufacturer’s

instructions and the advice on page 18.

Add any other laundry aids (see page 18). Close the

drawer again.

Wash by hand

Items labelled with the following symbol are not suitable for machine washing:

Dry clean

For very delicate items, such as net curtains, underwear, tights etc., you are advised to

use a laundry net or wash bag.

Selecting the wash programme

Woollen items must be labelled with the "Pure New Wool" symbol to be washed in the

machine

, and must also be labelled "non-matting" or "machine washable".

Note: when setting the programme, make sure that the

Start button is not pressed.

Colour often leaks from new coloured items.

This can then colour other lighter items being washed.

We therefore recommend that coloured items should be washed for the first time

separately.

Refer to the programme guide or the programme descriptions on the machine to select the

most suitable programme.

For future washes, colourfast items can only be washed with whites up to 40°C.

Turning the selector knob the required programme is activated.

When the START button is pressed the machine sets the working sequence in motion.

Note: when sorting laundry

Warning: If there is any break in the power supply while

the machine is operating, a special memory stores the

selected programme and, when the power is restored, it

continues where it left off.

check there are no metal objects in the laundry

(such as paper clips, safety pins, pins, coins

etc...);

button up pillowcases, fasten zips, hook & eye

fasteners, belts and long dressing gown cords;

remove curtain hooks;

Check that the tap is turned on and that the discharge

hose is positioned correctly.

pay close attention to the labels on items

if you notice stubborn stains whilst sorting the

laundry, remove them using a special detergent or

a special stain remover.

When the programme is finished

Wait for the door lock to be released (about 2 minutes after the programme has finished).

Switch off the machine by resetting the on/off button, turn the timer knob for wash programme

on the OFF position and open the door by pressing the door open button. Remove the

laundry. Turn off the tap.

We recommend that you do not do a full load of towelling items only as these become too

heavy since they absorb a lot of water.

TABLE OF PROGRAMMES

TEMP.

°C

WEIGHT

MAX

PROG.

FABRIC

PROGRAM FOR

Please read these notes

CHARGE DETERGENT

When washing heavily soiled laundry it is recommended the load is

reduced to 3 kg maximum.

❙

❙ ❙

❀

In programmes shown in the wash guide, automatic bleaching is

Resistant fabrics

90°

60°

●

possible by pouring the liquid bleach into the detergent draw

* Programmes according to CENELEC EN 60456.

4,5

Whites

Cotton, linen

Cotton, mixed

resistant

●

Whites with Prewash

The spin speed may also be reduced, to match any guidelines

suggested on the fabric label, or for very delicate fabrics cancel the

spin completely this option is available with a spin speed selector.

60°

40°

4,5

●

Fast coloureds

Cotton, mixed

Cotton

Fast coloureds

Get the best results from your new Candy machine

30°

4,5

To ensure you get the best results from your new Candy machine it

is important to use the right detergent in your everyday wash. There

are many detergents available in the market and making a choice

from the wide range available can often be confusing.

Non fast coloureds

●

Non fast coloureds

cold wash

Mixed fabrics and

synthetics

60°

At Candy we regularly test many different types of detergent to

assess which give the best wash results in our machines. We found

only one brand always lives up to our exacting standards and

provides outstanding cleaning across a broad range of dirt and

stains, as well as providing high levels of fabric care. That’s why

Candy gave Ariel their official seal of approval.

Fast coloureds with Prewash

●

Mixed, resistant

Cotton, mixed fabrics,

synthetics

Fast coloureds

●

Synthetics (nylon,

50°

40°

30°

Fast coloureds

perlon), mixed cotton

Non fast coloureds

●

Mixed, delicate

synthetics

Non fast coloureds

●

cold wash

40°

30°

Delicates

1,5

●

“MACHINE WASHABLE” woollens

Very delicate fabrics

Specials

●

30°

●

Hand wash

Rinse

FOR YOUR NEW WASHING MACHINE

Fast spin

Drain only

Mix & Wash system programme

4,5

●

M&W

40°

50°

Rapid 32 minute

Dosages

Detergents, washing aids and amounts to use

Only use detergents which are suitable for use in a washing machine.

You will obtain the best results from your wash with the minimum use of chemical products

and the best care for your laundry if you take into consideration the degree of soiling as well

as the type of detergent to choose.

Choice of detergent

General purpose detergents

Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for

use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.

Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,

cosmetics and oil.

The amount of detergent to use depends on:

- water hardness: depending on the hardness of the water and the type of detergent used, it

is possible to reduce the amount of detergent.

the degree of soiling: it is possible to reduce the amount of detergent used depending on

the degree of soiling.

These detergents are not suitable for washing stained laundry, as they do not contain

bleach.

amount of laundry: it is possible to reduce the amount of detergent when washing only a

small amount of laundry.

Biological detergents, not all the products available give a really thorough wash.

Special detergents

_FD_oo_{r n}s_oa_rmg_ae_{l a}f_no_dr_lop_wo_cw_ond_cee_nr_trad_tie_onte_dr_eg_tee_rgn_ent_{ts: for normally soiled laundry choose a}

Detergents for coloureds and delicates, without added bleach, also often without any

optical brightening agents, to preserve the colour.

programme without prewash.

Detergents for a thorough wash, without added bleach or enzymes, particularly suitable

for handling woollen fibres.

Put the detergent in compartment “II” of the drawer.

For heavily soiled laundry, choose a programme with prewash.

Put 1/4 of the detergent in compartment “I”, 3/4 in compartment “II” of the drawer.

When using water softeners, first put in the detergent, then add the softener to compartment “II”.

For highly concentrated detergents not in single dose format, follow what is shown on pack

exactly as regards type and amount of dosage.

Detergents for curtains with optical brightening agents, resistant to light, to prevent

yellowing from sunlight.

Special detergents for programmed use of chemical substances, depending on fabric

type, degree of soiling and water hardness.

Here basic detergents, softeners, bleaches/stain removers can be added separately.

To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids

provided in the detergent packaging.

Liquid detergent dosage

Additional laundry aids

Liquid detergents may be used in accordance with the instructions on the relevant

packaging, for all programmes without prewash, by using the special container which is

placed in the drum or, for those models that have it, in the special insert for liquid detergents.

Water softener, means less detergent can be used where water hardness is classed as

hard to very hard.

Prewash substances, for the programmed treatment of stains prior to the main wash.

Using them means the subsequent wash can be at a low temperature or with bleach-free

detergents.

Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.

If you own a tumble dryer, clothes are softened even without the use of a fabric softener.

Do not put solvents in the washing machine!

Keep detergents and other laundry products out of children’s reach.

Before pouring in the detergent check that there are no foreign bodies in the detergent

drawer.

Dosage details are usually shown on the detergent packaging. Follow those instructions.

Transporting the appliance or long

periods when appliance is not in

use

Cleaning and routine maintenance

Do not use alcohol-based scourers and /or thinners on the outside of your washing machine,

just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:

- Cleaning the drawer compartments.

If the appliance is being transported or is out of use for

long periods in unheated places, all remaining water

must be completely removed from the hoses.

Ensure mains power is off, then unclip the hose and

point it downwards into a basin until all the water has

emptied out.

- Cleaning the filter.

_EC_vl_ee_na_ifn_iti_isn_ng_ott_sh_trie_ctlyd_nr_ea_cw_esse_ar_ry,c_ito_ism_gop_oda_tr_ot_cm_leae_nn_tht_es

When finished, repeat the operation in the reverse order.

compartments for bleaching detergents and additives

occasionally.

A) To do this you just need to pull them out firmly, but

without forcing them.

B) Clean everything in the compartment under running

water.

C) Put everything back in its proper place.

Cleaning the filter

The washing machine is fitted with a special filter for

handling large deposits which could block the discharge

hose (coins, buttons etc.) and which can, therefore, be

easily retrieved.

We recommend that the filter be cleaned at least once

a month.

The cleaning operation is as follows:

1) Ease off the plinth cover as shown in picture.

2) Turn the filter anti-clockwise until it stops in the vertical

position. Remove and clean.

3) After cleaning, replace the filter. Then follow all procedures

described above in reverse order.

4) Insert the inner hinges of the plinth in the special grooves and slide over to the right to fix in

position securely.

Attention: if the filter needs cleaning while there is

washing still in the drum, follow the instructions on the

following page to empty the water. This will prevent

excessive loss of water via the filter.

Note:

The use of environmentally-friendly, phosphate-free detergents can have the following effects:

Investigating malfunctions

waste water from rinsing may be cloudier because of the presence of zeolites held in

suspension, without the rinse performance being adversely affected;

presence of white powder (zeolites) on laundry after washing, which is not absorbed by

the fabric and does not alter the colour of the fabric.

What might be the cause of…

Defects you can remedy yourself

The presence of foam in the final rinsing water is not necessarily an indication of poor

rinsing.

MALFUNCTION CAUSE

REMEDY

Anionic surfactants used in washing detergent formulae often prove to be difficult to

remove from the laundry itself and, even in small quantities, can still cause considerable

foam production.

1. Does not work on any

programme

Plug not in socket.

Not switched on.

Power failure.

Fuse blown.

Plug it in.

Switch on.

Check.

Carrying out more rinse cycles does not serve any purpose in such cases.

Check.

Door open.

Close door.

2. Does not fill with water

See cause 1.

Check.

Tap turned off.

Turn on tap.

Programme selector not correctly

positioned.

Position programme selector

correctly.

3. Water does not drain

away

Kink in discharge hose.

Foreign bodies in filter

Straighten discharge hose.

CUSTOMER SERVICE AND GUARANTEE

Examine filter (see pages 20-21)

4. Water on floor around

the washing machine

Leaking gasket between tap and water

inlet hose.

Replace gasket and tighten hose

and tap well.

Your new appliance is fully guaranteed by the manufacturer for 12 months against

electrical/mechanical breakdown excluding:

5. Does not spin

Water has not yet drained away.

"No spin" selected (certain models

only).

Wait a few minutes for machine to

empty.

A. Any faults which occur due to bad installation or misuse of the machine.

B. Any faults which occur due to repair of, or interference with, the machine by any person

not authorised by the manufacturer to carry out service.

Reset button or turn "no spin" knob.

6. Machine vibrates a lot

during spin

Washing machine not completely level.

Transit brackets not removed yet.

Load not distributed evenly.

Adjust the special adjustable feet.

Remove transit brackets.

C. Any faults which arise from parts fitted to the machine which are not the manufacturers

original parts.

Rearrange the laundry evenly.

D. Any faults arising from non-domestic use or unusual or abnormal use of the machine.

E. Any faults arising from operation at an incorrect voltage.

F. Any faults arising from incorrect operation of the machine.

The guarantee applies to Gt. Britain and Northern Ireland only, and is an addition to your

statutory rights.

7. Door will not open

Two minutes have not elapsed since

the programme finished.

Wait two minutes.

The machine makes a

different noise when

spinning! This is because it

has a manifold motor for

better performance.

Only a small level of water can be

seen in the drum! This is because

new machines do not use much

water, yet achieve the same

After Sales Service

If, having investigated the possible malfunctions on the chart on the previous page, you

believe the appliance is not working correctly, please call our After Sales Service dept. on

telephone number 08705 990011

standard of washing and rinsing.

SETTING UP + INSTALLATION

Remove the polystyrene base and place the machine near

its permanent position (diagram 1).

Carefully cut through the hose retaining clip at the rear of

the appliance (diagram 2).

Unscrew the central bolt (A); unscrew the 4 lateral screws

(B) and remove the cross piece (C) (diagram 3).

Lean the machine forward and remove the plastic bags

containing the two polystyrene blocks at the sides, pulling

downwards (diagram 4).

Press the plug (to be found in the envelope with the

instructions) into the hole and rotate to lock into position

(diagram 5).

Fig. 2

Technical data

■

Max. load of dry laundry

4,5 kg

■

Water pressure

0,05 ÷ 0,8 MPa

1400 rpm

■

Spin speed

Measurements

WARNING:

■

Width

Depth

Height

60 cm

52 cm

85 cm

DO NOT LEAVE THE PACKAGING WITHIN REACH OF CHILDREN AS IT IS A POTENTIAL

SOURCE OF DANGER.

■

NB: For specifications regarding electrical data, see the data panel on the front of the washing

machine (porthole area) - as shown in diagram above.

Apply the insulation sheet of corrugated material to the base

as shown.

EC Appliance complies with European Directive 89/336/EEC, 73/23/EEC and

subsequent amendments.

Level the machine by means of the front feet.

a) Turn the nut clockwise to release the screw adjuster on the foot.

b) Rotate the foot to raise or lower it until it stands

firmly on the ground.

c) Lock the foot in position by turning the nut

anti-clockwise until it comes up against the bottom of the machine.

Note: we recommend you keep the transit bracket,

braces and screws to immobilise the machine for future

transit.

Note: it is advisable to turn off the tap after each wash

to isolate the washing machine from the water supply.

The Manufacturers will not be responsible for any

possible damage to the machine caused by not

following the rules relating to releasing the mechanism.

The user is responsible for all costs of installation.

For the washing machine to function properly the terminal end of the discharge hose (mouth)

must be at a minimum of 50 cm and a maximum of 85 cm from the ground.

ELECTRICAL CONNECTIONS

After installation, the appliance must be positioned so that the plug is accessible.

If the plug we supply does not fit

CUT IT OFF AND DESTROY IT!

Water connection

You can’t use it on other appliances, and the exposed wires could be dangerous if plugged in.

To fit a replacement plug, proceed as follows:

The appliance must be connected to the water mains

using new hose-sets.

The old hose-sets should not be reused.

Your machine may either be plumbed in or connected

Connect

to the terminal in the plug

to existing taps, using a tap adaptor with a 3/4 B.S.P.

green and yellow wire

marked with the letter E,

OR marked

threaded end connection. The water supply hoses to

COLD

be found inside the drum are terminated in two

WATER

with the symbol,

different ways. One end which has a 90° elbow is to

OR coloured green,

OR coloured green and yellow.

be connected to the appliance water connection E

HOT

while the straight end is to be connected to the

WATER

domestic supply tap. The hose with the white collar

blue wire

marked N

should be connected to the cold tap, and the hose

with the red collar to the hot tap. The appliance is not

suitable for use with mixer taps.

OR coloured black.

brown wire

marked L

OR coloured red.

WARNING

This appliance must be earthed

min 4 cm

Fuses and plugs

This appliance should be used only on a socket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA

approved. Any replacement should be exactly the same.

+2,6 mt max

min 50 cm

max 85 cm

If the fuse cover is lost, do not use the plug until it is replaced. A correct replacement fuse

cover (obtainable from your local retailer) must be the same colour as shown or named on

the insert on the base of the plug.

......................................................................................................................................................................................................................

NOTES

The manufacturer declines all responsibility in the event of any printing mistakes in

this booklet. The manufacturer also reserves the right to make appropriate

modifications to its products without changing the essential characteristics.

Belshaw Brothers Convection Oven BXC Smartbake User Manual
Blue Rhino Patio Heater 200605C User Manual
Boston Acoustics Car Speaker SC50 User Manual
Briggs Stratton Portable Generator 40204 User Manual
Cadillac Mobility Scooter CTS V Series User Manual
Cambridge Audio CD Player 740C User Manual
Casio Trimmer DQ 683 User Manual
Chevrolet Automobile 2007 User Manual
Chief Manufacturing TV Mount PNR Series User Manual
Chromalox Electric Heater DU RAD 458 604 757 User Manual