St a t io n a r y SiD e Sh e l f Kit
SKSS2-1
Dr o p -Do w n Sh e l f
SKFB2-1
SKFPB2-1
re t a in ow n e r ’S Ma n u a l f o r fu t u r e re f e r e n c e .
Page 1
St a t io n a r y SiD e Sh e l f in S t a l l a t i o n
Stainless Steel Side Shelf
1. Removethecookinggrids, briquetsandbriquetrackfrom
the grill.
1
2. Attach the Handle Shelf Bracket to the grill using the Hex
Head Bolts, Flat Washers, Lock Washers, and Nuts. Do
not over-tighten.
2
3. Place the Tool Hook Bar inside the Shelf and place the
Shelf on the Bracket, aligning the screw hole. Insert the
Truss Head Screw and tighten. See Figure 1.
3
Index No.
Part No. Description
B076727 SIDE SHELF
B073971 TOOL HOOK
1
2
3
B101405 HANDLE SHELF BRACKET
B100002 HARDWARE PACKAGE
fig u r e 2
fig u r e 1
Dr o p -Do w n SiD e Sh e l f in S t a l l a t i o n
1
4
Index
No.
Part No. Description
1
2
2
3
3
4
5
B100561 Side Shelf
B100568 Support Bracket Front - Stainless Steel
B100559 Support Bracket Front - Black
B100569 Support Bracket Back - Stainless Steel
B100560 Support Bracket - Back - Black
B101370 Bracket Attach Assembly
B100993 Shelf Support Stiffener
2
3
5
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact
Broilmaster Customer Service • w w w .broilmaster.com. To ensure prompt and accurate service, please provide the following
information when placing a repair part order: Model Number of your grill, Part Name, Part Number, and Quantity of parts
needed.
B101559-3-0611
Page 3
Dr o p -Do w n SiD e Sh e l f in S t a l l a t i o n
Solid Surface Drop-Down Side Shelf
1. Remove the cooking grids, briquets and briquet rack from the grill.
2. Attach the Bracket Attach Assembly to the grill using the Truss Head Screws, Flat Washers, Lock Washers, and Nuts. See Figure 1.
Note: Ensure that the Bracket Attach Assembly is installed so that the match light access hole is on the bottom. See Figure 2
3. Place the Side Shelf upside down on a clean surface and use the four coarse-thread screws to loosely attach the Support Brackets.
4. Place the support stiffener on the inside of the shelf using (2) #10-16x1/2” screws to secure in place.
5. Hang the shelf brackets on the lower pins of the Bracket Attach Assembly. Tighten the four screws to secure the bracket arms to the
shelf. See Figure 3.
6. To raise the shelf - swing it out and lift the notches over the upper pins. Make sure the shelf is securely in position before placing any-
thing on it.
7. To lower the shelf - lift up on both brackets simultaneously and pull out slightly.
Correct Bracket Alignment
fig u r e 1
Incorrect Bracket Alignment
fig u r e 2
fig u r e 3
BROILMASTER®
A Division of Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Visit o u r w e b s it e a t w w w .broilmaster.com
If you have a general question about our products, please e-mail us at [email protected].
Page 4
B101559-3-0611
If you have a service or repair question, please contact your dealer.
|